No Water Pressure in House With a Well
A step-by-step guide for homeowners who suddenly have no water pressure with a well. What to check, what not to do, and when to call for emergency service.
No water pressure in a house with a well usually means the pump is not running, the pressure switch is not calling for water, or the pressure tank has lost its air charge. The first thing to check is the breaker. If the breaker is tripped, leave it off and call a well contractor. Flipping it repeatedly can burn out the pump. If the breaker is on but the gauge reads zero, the pressure switch, tank, or pump may have failed. This guide covers the safe checks and the fastest path back to water.
What our team handles on the call
- Answer the phone 24/7 for no-water emergencies
- Check the breaker, pressure switch, and tank charge
- Test the pump for power, amperage, and mechanical failure
- Replace switches, tanks, or pumps on the same visit when possible
- Restore water pressure and verify the system before we leave
How a service call works
- 1Call us, day or night
(336) 273-7314 is answered 24 hours a day, every day of the year. A real person picks up, not a recording.
- 2Quick phone triage
We confirm whether the issue is the pump, the pressure tank, the breaker, or something simpler we can talk you through right now.
- 3Dispatch to your door
A truck rolls with the common pumps, switches, tanks, and check valves needed to finish most no-water calls in one visit.
- 4Diagnose and fix
We restore water on the first trip whenever the parts and well allow. You see a written estimate before we touch anything.
- 5Tested before we leave
We cycle the system, confirm pressure, and shock-chlorinate the well anytime we have it open for a pump pull.
What does it cost?
A no-water-pressure call in central NC is typically resolved for $400 to $1,800 if the problem is a switch, tank, or minor pump repair. A full pump replacement runs $1,500 to $3,500. The on-site diagnosis is free, and we always give a written estimate before starting work.
- •Pressure switch or minor repair: $400 – $1,000
- •Pressure tank replacement: $600 – $1,400
- •Pump repair or replacement: $400 – $3,500
- •Free on-site diagnosis and written estimate
- •No after-hours upcharge
Every job gets a written, on-site estimate before any work begins. No surprise fees.
Where we work
We respond to no-water-pressure calls across the Piedmont Triad, including Greensboro, Winston-Salem, Burlington, High Point, Asheboro, Chapel Hill, and Kernersville.
Frequently asked
Why do I have no water pressure in my house with a well?
The most common reasons are a tripped breaker, a failed pressure switch, a waterlogged pressure tank, a burned-out pump, or a problem with the well itself. The first safe check is the breaker at the electrical panel. If it is tripped, leave it off and call a well contractor rather than resetting it repeatedly.
What should I do if my well pump breaker keeps tripping?
Leave the breaker off. A tripping breaker usually means the pump motor is drawing too much current because of a short, a bad capacitor, or a locked rotor. Resetting it repeatedly can destroy the motor and the pressure switch. Call a licensed well contractor for same-day diagnosis.
Can a pressure switch cause no water pressure?
Yes. A failed pressure switch may not close the circuit to the pump, so the pump never runs even though it is fine. It is one of the most common no-water causes and is usually a quick repair.
Can you come out the same day?
Yes. No-water calls get same-day priority across the Piedmont Triad and our phone is answered 24/7. Most emergency calls are reached on-site within a couple of hours of the first call.
Do you warranty the work?
Yes. You get the full manufacturer warranty on the pump or tank plus our own labor warranty on the install. We answer the phone after the job is done.
More reading
Need help right now?
We answer the phone 24/7. Most calls are reached on-site within a couple of hours.
Call (336) 273-7314Or send a message and we will get back to you.